Low Viscosity Silicone Conformal Coating
-
Payment
-
Origin
China Mainland
-
Minimum Order
15
-
Packing
Pieces
- Contact Now Start Order
- Description
Product Detail
If you are planning to wholesale best cheap and high quality low viscosity silicone conformal coating China, or hot sale low viscosity silicone conformal coating in China from professional low viscosity silicone conformal coating manufacturers and suppliers and factory, please feel free to contact SEPNA, and welcome to check products price with us.
SI 1921 is low viscosity ,no solvent organic silicone coating.
?Detailed Product Description
Features
1.Single component, low viscosity, solvent free, very convenient for application.
2.Environment friendly
3.High transparency, good adhesion
4.Good elastic and stabilize after curing at -60 - 200 ° C
5.Bond very well with surface of variety substrates, primerless.
6.Excellent waterproof, anti-corrosion, moisture, electrical insulation performance
Usage:
Used for protective coating of hard/soft printed circuit board and porous impregnating substrate
?Data Table
Composition | Organosilicone |
Appearance | Transparent fluid |
Viscosity CPS (25?) | 500 - 700 |
Specific gravity | 1.02 |
Mixture ratio | One component |
Solid content | 100 % |
Touch dry time | 18 mins,RT |
Curing conditions | 150? under = 5min |
Hardness (SHORE A) | 20 |
Tensile strength(MPa) | 0.5 |
Elongation at break (%) | 200 |
Share strength (MPa) | 0.5 |
Peel strength(N/mm) | >5 |
Dielectric strength (kV/mm) | 21 |
Dielectric constant (1.2MHz) | 3.0 |
Loss factor (1.2MHz) | 5×10-3 |
Volume resistivity (O·cm) | 5×1014 |
?Operation
Spraying
1.Use the dilunet according to you demand, can used without any diluent.
2.Diluted by diluent 1921, the volume of diluent will impact viscosity and the thickness of the glue.
2.Recommendations for the deployment of diluent 10% to 40%
3.Recommendations anhydrous toluene, petroleum ether for diluent, should not be used alcohols/ ketones solvents
4.Transferred to a watering pot and be sprayed directly
5.Use diluent to clean watering pot after spray
6.Application with good ventilation space
Brushing
1.Prepare, anti-static brush or brush, etc.;
2.Open the barrel
3.Use the brush for selective brushing, brushing the second time after dry of the first floor, brushing times is depend on the demand thickness.
Dip coating
1.Put the diluted gel in bucket to dip coating
2.To avoid bubbles the dipped speed of PCB immersion should not be too fast.
3.The touch dry time in the room temperature about 40mins, heat stoving is not recommend
4.Removal of the epidermis can continue to use.
?Package and Storage
Package
1kg/20kg Barrel
Storage
Keep in cool and ventilative place Temperature=35?
Shelf life: 12 months (25?)
These products don't belong to dangerous goods, so they can be transported as normal chemicals. But be careful of Leakage.
Confirming the condition of the products that out of deadline before using.
Application method can consult the marketing department.
?Safety Operation Material
MSDS isn't included here. Please read TDS, MSDS and label carefully before operation.You can get MSDS from SEPNA or other distributors, or mail to service center sepna@sepna.cc, or call +86-400-882-1323.
?Product Warranty
All product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advices we supply don't apply in any circumstances. SEPNA don't make assurance of any other applications outside the specification until SEPNA supply a special written guarantee. SEPNA is only responsible to replace or refund if this product is defective within the warranty period stated above. SEPNA makes it clear that will not be liable of any accidents.
- Silicone Lubricating Grease 15 Pieces / (Min. Order)
- One Part Thermal Paste 15 Pieces / (Min. Order)
- Thermally Conductive Silicone Sealant 15 Pieces / (Min. Order)
- RTV Heat Resistance Red Silicone Sealant 15 Pieces / (Min. Order)
- High Strength Epoxy Adhesive 15 Pieces / (Min. Order)
- Fast Curing Structural Epoxy Adhesive 15 Pieces / (Min. Order)
- Transparent Fast Curing Structural Epoxy 15 Pieces / (Min. Order)
- Medical Grade Liquid Silicone 15 Pieces / (Min. Order)
- Transparent Liquid Silicone Gel 15 Pieces / (Min. Order)
- 2 Parts Silicone Gel For Electronics 15 Pieces / (Min. Order)
- Silicone Gel For Electrical Insulation 15 Pieces / (Min. Order)
- Transparent Silicone Gel For PCB Board 15 Pieces / (Min. Order)
- Two Part Polyurethane Resin 15 Pieces / (Min. Order)
- Two Part Polyurethane Potting Compound 15 Pieces / (Min. Order)
- Urethane Potting Compound 15 Pieces / (Min. Order)
- Two Parts Epoxy Adhesive For Betteries 15 Pieces / (Min. Order)
- Black Epoxy Potting Compound 15 Pieces / (Min. Order)
- High Bonding Strength MS Sealant 15 Pieces / (Min. Order)
- Acrylic Waterproof Coating 15 Pieces / (Min. Order)